Pump Spare Parts (PrimeLine™)

PrimeLine™ Pump Replacement Parts

Whether they are check valves, pistons or pump seals, all PrimeLine™ Pump Replacement Parts are designed to exceed the manufacturers specifications. All parts are subjected to rigorous engineering analysis and quality standards to insure the parts you purchase provide maximum life and superior chromatographic performance. Replacement parts are available for most HPLC/UHPLC pumps.

  • Majority of check valves are self-priming, no external priming valve/syringe required
  • Designed to deliver superior flow stability and accuracy
  • Crush proof cartridge makes routine maintenance quick and easy
  • Pistons are engineered to insure a high quality surface finish
  • Seals are designed for long life, wide range of solvent compatibility, and optimum performance

 

Why PrimeLine™  Check Valves are the Best


Self-priming

With the PrimeLine  valve, priming is easy.  Open the pump outlet to release backpressure on the pump, and turn on the pump.  Your pump will prime itself, even if the head and intake lines are completely dry.  You won't need to use syringes or draw-off valves to prime your pump.

 

Superior Flow Rate Stability

Because of the rapid and repeatable closure rate of the valve, the ball returns to the seat and seals before solvents have a chance to flow back through the valve.  The result is a flow rate that is extremely repeatable and accurate, which means more repeatable retention times.   

 

Rugged Construction

The valve will not crush, crack or leak due to high pressure.  We designed the PrimeLine™cartridge so that loads are transmitted through the valve casing rather than through the seat, as in conventional valves.  The result is a valve that can withstand up to a 10,000 PSI continuous operating pressure, and will never fail no matter how much you tighten the housing (go ahead and try it -- it's guaranteed!).  High pressure valves, up to 15,000 PSI, are also available.   

 

Pre-tested

100% PrimeLine valves we ship must pass three stringent tests before it is shipped.
These tests are by far the most stringent in the HPLC industry, and indeed it is unlikely that any other valves would even pass these tests. But we do all these tests because we know how important it is to make sure that when you put a new valve in your pump, it will perform properly. After all, HPLC is hard enough as it is without worrying about your check valves!

1) Self-prime Test

This test uses a special pump test fixture that simulates an HPLC pump to verify that the valve is self-priming.  After the test pump and intake line are purged of water, the valve must operate well enough so that the pump can draw water from a reservoir that is 36 inches below the pump intake.  If the valve fails to prime, or "skips" even once during this test, it is rejected.  This test not only guarantees that the valve will prime, but also that the valve will perform properly even at very low pressures, where most other valves do not work well.

2) High Pressure Leak Test

The valve is pressurized to 12,000 PSI and tested for leakage. Valves that exceed 50 nano liters per minute are rejected. This test not only insures valve integrity at very high pressures, but it also insures that the valve will still function properly even when the customer inadvertently over tightens the valve housing. We do not monitor nitrogen bubbles to measure leak rate, because a liquid can leak due to capillary action whereas gas will not. Besides, the chromatographer is pumping liquids, not gas!

3) Low Pressure Leak Test

The valve is pressurized to 500 PSI and tested for leakage. Valves that exceed 50 nano liters per minute are rejected. Most valves have difficulty closing and sealing properly in the absence of the large closing forces due to high pressure. ASI valves are designed so that they do not require any backpressure to operate properly, and this test verifies it.

Convenient and Economical Cartridge Design

When it's time for routine maintenance, you only replace the cartridge, not the entire assembly.  The PrimeLine cartridge costs no more than most conventional valve rebuild kits, and you won't spend time chasing balls all over the lab bench.

Downloads
Selection Guide for material of pistons seals
PrimeLineTM Replacement Parts Brochure

 

410 Results

Per Page
To top